113 results for “Motor Control Units Buying Leads, Buyers & Importers”

1. Semi Hermetic Compressor for R-290 Refrigerant, qty: 8 units Semi hermetic electrical driven compressor, 2 cylinder, displacement approx. 13.70 m3/h at 50HZ, 220-380V, frequency range 30-70 HZ, with oil return valve, including oil sump heater 230 V - 1 - 50/60 Hz, 160 W and smart start. 2. Motor Belt Drive Compressor 4-6 kW for R-290 Refrigerant, qty: 8 units Motor belt driven compressor, 145 cc/rev max. 6000 rpm, with oil return valve with 12/24 V clutch, flexible hoses 1 m for suction and liquid side, oil return flexible hose 0.5 m, and mounting accessories.

1. Semi Hermetic Compressor for R-290 Refrigerant, qty: 8 units Semi hermetic electrical driven compressor, 2 cylinder, displacement approx. 13.70 m3/h at 50HZ, 220-380V, frequency range 30-70 HZ, with oil return valve, including oil sump heater 230 V - 1 - 50/60 Hz, 160 W and smart start. 2. Motor Belt Drive Compressor 4-6 kW for R-290 Refrigerant, qty: 8 units Motor belt driven compressor, 145 cc/rev max. 6000 rpm, with oil return valve with 12/24 V clutch, flexible hoses 1 m for suction and liquid side, oil return flexible hose 0.5 m, and mounting accessories.

We are looking to purchase Mixed Electric Motor Scrap and would appreciate your detailed quotation and confirmation on the following specifications: 1. Quantity Required: 25 Metric Tons 2. Export Capability to India: Can you export to Indian ports? (Preferred ports: Nhava Sheva/Mundra/Chennai) What is your monthly export capacity to India? Typical lead time from order confirmation to FOB shipment? Experience with Indian importers/customs clearance for electric motor scrap? 3. Material Specifications: Copper Recovery Rate: What is the guaranteed minimum copper recovery % from these motors? (e.g., 12-18% typical for mixed motors) Casing Material: What material is the motor casing made of? (Steel, cast iron, aluminum?) Motor Types: Mix of AC/DC, fractional horsepower, sealed units, etc.? Size Range: Maximum dimensions? (e.g., up to 3ft diameter x 3ft length) Condition: Drained of oil/fluids? Free from hazardous contamination? 4. Commercial Terms: Price: USD ___ per MT FOB [your port, e.g., Laem Chabang/Chonburi] Payment: [Your preference, e.g., MT103 after documents / DLC / etc.] Inspection: SGS/Bureau Veritas pre-shipment at buyer’s cost Documentation: Full set BL, CI, PL, COO, SGS report, HS Code confirmation (typically 8503 for electric motors scrap) 5. Additional Information Required: Photos/samples of current stock SGS analysis report (if available) Export license/approvals for India shipment Packing method (loose/container/bales) Please provide your best FOB price along with answers to the above points. Looking forward to your prompt response.

We are looking to purchase Mixed Electric Motor Scrap and would appreciate your detailed quotation and confirmation on the following specifications: 1. Quantity Required: 25 Metric Tons (±5% at seller's option) 2. Export Capability to India: Can you export to Indian ports? (Preferred ports: Nhava Sheva/Mundra/Chennai) What is your monthly export capacity to India? Typical lead time from order confirmation to FOB shipment? Experience with Indian importers/customs clearance for electric motor scrap? 3. Material Specifications: Copper Recovery Rate: What is the guaranteed minimum copper recovery % from these motors? (e.g., 12-18% typical for mixed motors) Casing Material: What material is the motor casing made of? (Steel, cast iron, aluminum?) Motor Types: Mix of AC/DC, fractional horsepower, sealed units, etc.? Size Range: Maximum dimensions? (e.g., up to 3ft diameter x 3ft length) Condition: Drained of oil/fluids? Free from hazardous contamination? 4. Commercial Terms: Price: USD ___ per MT FOB [your port, e.g., Laem Chabang/Chonburi] Payment: [Your preference, e.g., MT103 after documents / DLC / etc.] Inspection: SGS/Bureau Veritas pre-shipment at buyer’s cost Documentation: Full set BL, CI, PL, COO, SGS report, HS Code confirmation (typically 8503 for electric motors scrap) 5. Additional Information Required: Photos/samples of current stock SGS analysis report (if available) Export license/approvals for India shipment Packing method (loose/container/bales) Please provide your best FOB price valid for 7 working days, along with answers to the above points. Looking forward to your prompt response.

Dear supplier, We are urgently in need of 3 units of Wood Disc Chipper Machines with the following specifications: - Disc Size: ±2500 mm with ±250 KW Motor or Diesel machine - Vertical input (45°) - Input size: 500x500 mm Included: - Wood chip discharge conveyor: 1m x 10m - Wood log conveyor: 1m x 6m - Vibration screen: 50 tph, with qualified wood chip discharge conveyor: 1x12m, Extra large wood chips back to chipper conveyor: 0.6x12m Trade term: CIF Payment term: TT Target Price: Negotiable Thank you.

Item Green Robusta Coffee Quantity 60 tons (60 x 12 unspecified units - assuming bags or similar) Coffee Type S 18 Category (Not specified beyond "Coffee Category") Origin Current Crop Max Moisture 13% Max Foreign Matter 1% Max Defects 60 per 300 grams (Le Havre grading, Screen 14/18) Packaging Jute bags Compliance Must meet at least CODEX Alimentarius specifications Samples Request via DHL, buyer willing to pay costs Note Recommended by state control services for import agreement renewal CIF Rades port Payment and Inspection Terms Payment Method Irrevocable LC at sight confirmed from top bank Payment Transfer MT 103 at loading port after SGS or equivalent SGS Loading Port Seller's cost Final Inspection SGS or equivalent at destination port (buyer's cost)

We are looking for these products: 1) Required generator sizes (same manufacturer) Unit 1 (Single phase): 7 to 8 kilovolt-ampere rated output 230 volt, 50 hertz, single phase Silent canopy Unit 2 (Three phase): 15 to 20 kilovolt-ampere rated output (18 preferred) 400 volt, 50 hertz, three phase Silent canopy Both units must be supplied by the same factory and preferably the same platform family. 2) Full autonomous start requirement (non-negotiable) Both units must start and stop automatically with: Two-wire dry contact start input terminals for automatic transfer switching No key fob remote start as the primary method Designed for unattended standby operation 3) Controller input and output signals (non-negotiable) Controller must provide at minimum: Start input Running status output Alarm or fault output Fault log preferred 4) Standby cold-start logic (non-negotiable) Automatic glow plug and preheat control Reliable cold start without manual intervention 5) Power quality and step-load performance (non-negotiable) Stable voltage and frequency suitable for inverter and battery charger loads Must tolerate step-load without stalling or unstable speed hunting 6) Noise target (non-negotiable) 70 decibels or less at 7 metres at 50 percent load Must be silent canopy type 7) Fuel system requirement (non-negotiable) Fuel filtration including water separator Serviceable filterwhile in field use - Trade term: EXW (factory) first, later FOB. - Payment term: sample order by T/T 100%. Production: 30% deposit, 70% before shipment (negotiable for larger orders). - Quantity: 1–2 samples first, then 20–50 units per order, scaling to 100+ units. Destination port: Brisbane, Australia. - Trade terms are irrelevant if the offered products do not meet the required specifications. Petrol generators EFI is the required hard technical gate. Carburettor and choke systems are inherently unreliable after standby periods and are therefore not acceptable for unattended operation. This requirement is clearly stated in the petrol RFQ: EFI is mandatory, unless the manufacturer can provide documented, factory-proven evidence of a system designed and validated for reliable unattended starting. Diesel generators Proper glow plug and preheat logic is the required hardware and control requirement. “Electric start” alone is not sufficient if the controller does not execute temperature-based preheat, start retry logic, and fail-to-start alarms. These requirements are explicitly defined in the diesel RFQ and the acceptance protocol.

We are looking to purchase Mixed Electric Motor Scrap and would appreciate your detailed quotation and confirmation on the following specifications: 1. Quantity Required: 25 Metric Tons (±5% at seller's option) 2. Export Capability to India: Can you export to Indian ports? (Preferred ports: Nhava Sheva/Mundra/Chennai) What is your monthly export capacity to India? Typical lead time from order confirmation to FOB shipment? Experience with Indian importers/customs clearance for electric motor scrap? 3. Material Specifications: Copper Recovery Rate: What is the guaranteed minimum copper recovery % from these motors? (e.g., 12-18% typical for mixed motors) Casing Material: What material is the motor casing made of? (Steel, cast iron, aluminum?) Motor Types: Mix of AC/DC, fractional horsepower, sealed units, etc.? Size Range: Maximum dimensions? (e.g., up to 3ft diameter x 3ft length) Condition: Drained of oil/fluids? Free from hazardous contamination? 4. Commercial Terms: Price: USD ___ per MT FOB [your port, e.g., Laem Chabang/Chonburi] Payment: [Your preference, e.g., MT103 after documents / DLC / etc.] Inspection: SGS/Bureau Veritas pre-shipment at buyer’s cost Documentation: Full set BL, CI, PL, COO, SGS report, HS Code confirmation (typically 8503 for electric motors scrap) 5. Additional Information Required: Photos/samples of current stock SGS analysis report (if available) Export license/approvals for India shipment Packing method (loose/container/bales) Please provide your best FOB price valid for 7 working days, along with answers to the above points. Looking forward to your prompt response.

Kindly send a quotation based on the following request from the importer: Product Name: Agriculture Sprayers Type: Single or Double Motor Battery Spray Use: For spraying fertilizers and pesticides in fields Quantity: 300-600 units Trade Term: CIF Payment Term: TT Target Price: Negotiable

Kindly provide a quotation based on the following request from the importer for a Fish Pond Filtration System. The product requested is a fish pond drum filter with the following specifications: - High volume flow: 30m³/h - Roller motor: 40W - Inlet: 63mm*2 Quantity required: 2 units Trade Term: CIF Payment Term: Bank Transfer Target Price: Negotiable.

Please submit your quotation for the following product specifications: Electric Knife Set, Model No. 74312G, intended for domestic kitchen use, with a motor power of 120 Watts. The product features stainless steel serrated blades, a plastic handle, a power on/off button, contoured grip with touch control button, and operates at 120V, 60Hz. Quantity: 3,000 units. Payment term: Giro Directo. Destination port: Barranquilla Customs.

Kindly send a quotation based on the following request from the importer: 200 pieces of various automotive and electrical components including motor vehicle parts, control cables, electrical components, copper threaded articles, and brass electrical switch parts. The destination port is Newark, New Jersey, United States.

Please submit your quotation for the following product specifications: Motor Reservorio Plumas, Quantity: 3 units, Destination Port: Guayaquil - Maritimo.

Please submit your quotation for the following product specifications: Motor Reservorio Plumas, Quantity: 10 units, Destination Port: Guayaquil - Maritimo.

Send your quotation based on the importer’s request below: Quantity: 20 units of Motor Plumas, destination port: Guayaquil - Maritimo.

Please submit your quotation for the following product specifications: Motor Reservorio Plumas, Quantity: 3 units, Destination Port: Guayaquil - Maritimo.