9 results for “Motorcycle Fuel System Buying Leads, Buyers & Importers”

Type Electric / Gas / Diesel / Biomass Steam Generator (supplier’s recommendation acceptable) Steam Capacity 300–2000 kg/h (adjustable according to actual process) Rated Pressure 0.7–1.3 MPa Steam Quality Dryness ≥ 96% Feed Water Softened or purified water Thermal Efficiency ≥ 90% (electric), ≥ 88% (fuel-fired) Control System PLC automatic control with low-water, over-temperature, and over-pressure protection Installation Compact, factory-tested, ready for installation Dimensions Supplier to provide detailed drawings and space requirements Standards Compliance ASME / CE / GB / JIS or equivalent Operating Conditions Application: Food processing / Beverage bottling / Pharmaceutical cleaning and sterilization Operating Hours: 8–16 hours per day Power Supply: 380V / 50Hz (or as applicable) Ambient Temperature: 5–45 °C

We are looking for these products: 1) Required generator sizes (same manufacturer) Unit 1 (Single phase): 7 to 8 kilovolt-ampere rated output 230 volt, 50 hertz, single phase Silent canopy Unit 2 (Three phase): 15 to 20 kilovolt-ampere rated output (18 preferred) 400 volt, 50 hertz, three phase Silent canopy Both units must be supplied by the same factory and preferably the same platform family. 2) Full autonomous start requirement (non-negotiable) Both units must start and stop automatically with: Two-wire dry contact start input terminals for automatic transfer switching No key fob remote start as the primary method Designed for unattended standby operation 3) Controller input and output signals (non-negotiable) Controller must provide at minimum: Start input Running status output Alarm or fault output Fault log preferred 4) Standby cold-start logic (non-negotiable) Automatic glow plug and preheat control Reliable cold start without manual intervention 5) Power quality and step-load performance (non-negotiable) Stable voltage and frequency suitable for inverter and battery charger loads Must tolerate step-load without stalling or unstable speed hunting 6) Noise target (non-negotiable) 70 decibels or less at 7 metres at 50 percent load Must be silent canopy type 7) Fuel system requirement (non-negotiable) Fuel filtration including water separator Serviceable filterwhile in field use - Trade term: EXW (factory) first, later FOB. - Payment term: sample order by T/T 100%. Production: 30% deposit, 70% before shipment (negotiable for larger orders). - Quantity: 1–2 samples first, then 20–50 units per order, scaling to 100+ units. Destination port: Brisbane, Australia. - Trade terms are irrelevant if the offered products do not meet the required specifications. Petrol generators EFI is the required hard technical gate. Carburettor and choke systems are inherently unreliable after standby periods and are therefore not acceptable for unattended operation. This requirement is clearly stated in the petrol RFQ: EFI is mandatory, unless the manufacturer can provide documented, factory-proven evidence of a system designed and validated for reliable unattended starting. Diesel generators Proper glow plug and preheat logic is the required hardware and control requirement. “Electric start” alone is not sufficient if the controller does not execute temperature-based preheat, start retry logic, and fail-to-start alarms. These requirements are explicitly defined in the diesel RFQ and the acceptance protocol.

Type Electric / Gas / Diesel / Biomass Steam Generator (supplier’s recommendation acceptable) Steam Capacity 300–2000 kg/h (adjustable according to actual process) Rated Pressure 0.7–1.3 MPa Steam Quality Dryness ≥ 96% Feed Water Softened or purified water Thermal Efficiency ≥ 90% (electric), ≥ 88% (fuel-fired) Control System PLC automatic control with low-water, over-temperature, and over-pressure protection Installation Compact, factory-tested, ready for installation Dimensions Supplier to provide detailed drawings and space requirements Standards Compliance ASME / CE / GB / JIS or equivalent Operating Conditions Application: Food processing / Beverage bottling / Pharmaceutical cleaning and sterilization Operating Hours: 8–16 hours per day Power Supply: 380V / 50Hz (or as applicable) Ambient Temperature: 5–45 °C

Send your quotation based on the importer’s request for A1 Jet Fuel: - Quantity: 10,000,000 barrels monthly for 60 months - Trade Term: TTT, FOB - Payment Term: MT 103, SBLC - Packaging: Customized - Buyer uses a one-time QR system for Houston contracts and renewable SBLC for term contracts after successful spot & title transfer. Compliance documentation is prepared. Target price is negotiable.

Send your quotation based on the importer’s request below: We are looking to purchase A1 Jet Fuel in a contract volume of 10 million barrels per month for a duration of 60 months. The buyer requires the use of a one-time QR system upon title transfer for contracts in Houston. The preferred trade terms are TTT and FOB, with payment terms including MT103 and SBLC. Packaging terms are to be customized. For Rotterdam contracts, the ICPO should be issued and signed with a PROCEDURE CI, followed by the issuance of POP including SGS, TSR, OTA, ATV, Injection Report, and ATSC. The buyer will verify and pay MT103 within 24-48 hours, with a renewable SBLC for the term contract after a successful spot and title transfer. For Houston contracts, the ICPO with PROCEDURE CI should be issued and signed with a one-time QR code upon title transfer, excluding TSA/TSR. The POP should include SGS, Product Passport, Accreditation Cert, ATSC, CI, ATV, etc. Payment will be made by the buyer after document review and confirmation, followed by a renewable SBLC for the term contract after a successful spot and title transfer. The buyer is ready to proceed if we can offer a price competitive with their current supplier. Compliance documentation has been prepared for this transaction. Kindly provide your quotation based on these specifications.